$SAVE$ Telephone Signaling; Ringers, Bells, Horns, Strobes, TeleStrobe, Alerts,Telephone Alert,Loud Ringer, Chime, Loud Horn, TelBell,telephone alert light,1791-sl,1791,Telehorn,Telechime,TB-591,TB-592,TB-593,1791-MT,1791-B,CH-AT1,CH-AT2,CH-BT1,CH-BT1,CH-BT2,CH-BT4,telephone ringer outdoors,blk-3-ewp,viking,strobe light,vr-1a,vr1a,ca-312,ca312,ca-622,ca622,MTH-24,MTH24


SIGNALING & ALERTS	Ringers - Bells - Horns - Strobes

Telephone Ringers, Bells, Horns & Strobes

DESCRIPTION

IP/Digital Phone System Applications	Do you need an IP or Digital Phone System interface to operate your ringers, strobes or bells?
TelChime (AT Series)	Provides a pleasant signal as an alternative to standard telephone bell ringers & electronic warblers. Recommended for small office environments.
TelChime (BT Series)	Provides a pleasant signal as an alternative to standard telephone bell ringers & electronic warblers. Louder than the AT Series.
TeleStrobe	Signaler emits a high intensity flashing light when the telephone rings. Ideal for noisy environments, for quiet zones in hospitals or libraries and for alerting deaf or hard-of-hearing individuals
Strobe Light one million candle power	Provides high visibility indication of analog line status through a high powered one million candle power strobe light. The BLK-3-EWP is the ideal solution for the hearing impaired and can be used equally well in loud warehouses or factories, where ringing phones can not be heard.
Universal Telephone Alert	High dBA (109 dB) and low current draw. Strobe version emits flashing light when telephone rings.
Phone Strobe Flasher	Strobe light flashes to alert you to incoming calls
Phone Strobe Flasher w/ringer	Amplified ringer with strobe light
TelBell	Bell alert designed or use in noisy locations for medium to large areas
Multi-Tone Loud Horn	Loud, weather resistant, attention getting alert
TeleHorn See MTH24 or UTA	Loud, weather resistant, attention getting alert
COLORED Light Strobes	Wall or Ceiling Mountable, available in several colors
Audible Control Units	Monitors analog tip & ring lines to provide call signaling, zoned signaling or night bell connection.
Dry Contact Closure Interface	Provides the power to operate a wide variety of 24 VDC signaling products
Visual Ring Indicator	Provides line status and message waiting indication
Super Loud Ringer	Adjustable 95+ db Super Loud Ringer w/Red Ringer Flasher
Message Waiting LED Lamp Kit	Provides visual indication of message waiting and ringing

TelChime AT Series	MODEL#	SIGNAL TYPE	RECOMMENDED coverage area	Nominal Input Current or Voltage	Input Current or Voltage Range	dBA @ 1 Meter
	AT1	Chime	Up to 1,000 sq. ft	90 VMRS, 20-30 Hz	50-130 VRMS, 20-30 Hz	80
	AT2	Chime	Up to 1,000 sq. ft	.02 Amps	18-30 VAC or VDC	80

product specs.

Provides a pleasant signal as an alternative to standard telephone bell ringers & electronic warblers.

Recommended for small office environment

Designed for use on public telephone networks or behind PBX & Key systems that use interrupted ringing voltages from 50-130 VAC, 20-30 Hz

Telchime produces a single chime sound during each cycle of interrupted ringing voltage.

Has volume control. For Bass/Treble Tone control model go to AT2 model.

Recommended for use indoors up to 1,000 sq

For larger areas go to the BT Series

For applications with more than 1 line CLICK HERE

product specs.

Dry Contact Closure may be required

Provides a pleasant signal as an alternative to standard telephone bell ringers & electronic warblers.

Same as the AT1 except allows tone control (Bass/Treble adjustment)

Recommended for small office environment

Designed for use with telephone communication systems .

Telchime produces a single chime sound during each cycle of interrupted ringing voltage. Both tone & loudness are adjustable.

Recommended for use indoors up to 1,000 sq

For larger areas go to the BT Series

For applications with more than 1 line CLICK HERE

TelChime BT Series	MODEL#	SIGNAL TYPE	RECOMMENDED coverage area	Nominal Input Current or Voltage	Input Current or Voltage Range	dBA @ 1 Meter
	BT1	Chime	1,000-5,000 sq. ft.	90 VMRS, 20-30 Hz	40-130 VRMS, 20-30 Hz	90
	BT2	Chime	1,000-5,000 sq. ft.	.02 Amps	18-30 VAC or VDC	90
	BT4	Chime	1,000-5,000 sq. ft.	90 VMRS, 20-30 Hz	38-60 DC Only	90

product specs.

Provides a pleasant signal as an alternative to standard telephone bell ringers & electronic warblers.

Designed for use on Public Telephone Networks or behind PBX & Key Systems that use interrupted ringing voltages from 40-130 VAC, 20-30 Hz.

Telchime produces a single chime sound during each cycle of interrupted ringing voltage.

Has volume control. For Bass/Treble Tone control model go to BT2 model.

Recommended for use indoors for 1,000-5,000 sq. ft

For applications with more than 1 line CLICK HERE

product specs.

Dry Contact Closure may be required

Provides a pleasant signal as an alternative to standard telephone bell ringers & electronic warblers.

Designed for use with telephone communication systems that use interrupted ringing voltages from 18-30 VAC or VDC

Telchime produces a single chime sound during each cycle of interrupted ringing voltage.

Both tone (bass & treble) & loudness are adjustable.

Recommended for use indoors for 1,000-5,000 sq. ft

For 38-60 DC Only applications go to BT4 Model

For applications with more than 1 line CLICK HERE

product specs.

Provides a pleasant signal as an alternative to standard telephone bell ringers & electronic warblers.

Designed for use with telephone communication systems that use interrupted ringing voltages from 38-60 DC only.

Telchime produces a single chime sound during each cycle of interrupted ringing voltage.

Telchime produces a single chime sound during each cycle of interrupted ringing voltage. Both tone (bass & treble) & loudness are adjustable.

Recommended for use indoors for 1,000-5,000 sq. ft

For applications with more than 1 line CLICK HERE

TELESTROBE

This compact signaler emits a high intensity flashing light when the telephone rings. Ideal for noisy environments, for quiet zones in hospitals or libraries and for alerting deaf or hard-of-hearing individuals.

	High intensity flashing light
	Easy to mount to any surface
	Solid-state design for high brightness, long life and low power consumption
	ADA compliant
	Available in 3 models; 115 VAC, Ring Voltage Powered & AC/DC Powered

For applications with more than 1 line CLICK HERE

Dry Contact Closure may be required for PS-33A

Product Specs

Applications

The BLK-3-EWP provides high visibility indication of analog line status through a high powered one million candle power strobe light. The BLK-3-EWP is the ideal solution for the hearing impaired and can be used equally well in loud warehouses or factories, where ringing phones can not be heard. Alternatively, the BLK-3-EWP can be used to add emergency notification to pre-existing emergency phones by turning on the strobe light when the emergency phone is in use.

The included LDB-3 control module has a disable input which is ideal for two-button emergency phones, such as Viking’s E-1600-20A, allowing "Info" button calls to be placed without activating the relay (turning on the emergency strobe light, camera, etc.) Three DIP switches are provided for turning ring detection on or off, off-hook/loop detection on or off and for selecting a ring cadence mode which allows the relay to follow ringing or to remain activated during the off time of standard ring cadence.

The control module can be installed on any standard telephone line or analog PABX/KSU station. The 1 million candle power strobe can be interfaced to flash on ringing, off-hook or a combination of ringing and off-hook (line in-use). The LDB-3 ring/loop detect control module is also available separately.

The kit includes: (1) LDB-3 control module, (1) blue strobe light, (1) 12V DC power adapter, (13) gel filled butt connectors and (1) single gang weatherproof mounting box with gaskets and hardware.

Applications

	Ringing Phone or TTY indication for the hearing impaired
	Ringing phone indication in loud warehouses and factories
	Emergency illumination for emergency phones in elevators, campuses, hallways, parking ramps, etc.
	Alarm indication for security systems or alarm panels with phone dialers

Features

	LDB-3 control module with Enhanced Weather Protection (EWP) included
	Polycarbonate lens
	Strobe and control module may be installed separately
	Long life 1 million candle power blue strobe light
	Flush mount or surface mount with weatherproof single gang box (included)
	3/4" knockouts for connecting conduit, etc.
	Can be configured to signal ringing off-hook or a combination of both ringing and off-hook (line in-use)
	One set of (NO) normally open and (NC) normally closed relay contacts provided
	Selectable ring cadence mode (strobe light will remain flashing between rings)
	Switched 12V DC output (follows relay activation for powering strobe lights, cameras, etc.)
	On/off switches for ring detection and off-hook/loop detection
	Disable input, ideal for use with two-button emergency phones (E-1600-20A), will not activate strobe light on "Info" calls
	One year warranty
	Made in the USA.

without Strobe

-------------

with Strobe

	High dBA (109 dB) and low current draw
	One unit for most telephone systems with easy dip switch selection
	Standard RJ11C phone jack connection (USA) or CA-11 jack (Canada)
	Attractive indoor and outdoor mounting options
	Power Supply Required (NOT INCLUDED) Contact Product Tech Support to determine Power Supply Voltage Requirements based on application. Product Specs For applications with more than 1 line CLICK HERE Dry Contact Closure may be required

It's almost impossible to miss telephone calls when you have the Phone Strobe Flasher. The bright strobe light connects to your phone line and flashes to alert you to incoming calls.

	Very easy to install
	Telephone line powered (no batteries needed)
	Durable design

For applications with more than 1 line CLICK HERE

When a phone call comes in, a bright strobe light flashes and an adjustable, extra loud amplified ringer sounds so that calls are never missed again. Up to 120+ dB. White only

	Telephone line powered (no batteries needed)
	Durable design
	Ringer high/mid/low switch
	Tone control hi/low switch

For applications with more than 1 line CLICK HERE

TELBELL

	Aluminum bell housing
	Integral RFI suppression
	Screw terminal connections and RJ-11 plug
	Tamper resistant volume control
	Weatherproof back box for indoor/outdoor mounting included
	6" Shell Size

For applications with more than 1 line CLICK HERE

Dry Contact Closure may be required for TB-592

MODEL #	PRICE	Product Specs	INPUT VOLTAGE	INPUT CURRENT	dBA @ 10 Feet
TB-591	Discontinued		38-60 VDC	0.025	100
TB-592	$95 for digital phones		18-30 VAC/DC	0.025/.030	100
TB-593	$95 for analog phones		55-130 V, 20-30 Hz	N/A	95

Dry Contact Closure may be required

For applications with more than 1 line CLICK HERE

	117 DB @ 1 Meter
	24 VDC Horn
	Built in 10 watt amplifier
	Telephone Extension Alert
	Auxiliary Alert
	Wall or Ceiling Mount
	Replacement for TeleHorn

MTH Installation

MTH Specs

COLORED LIGHT STROBES

CSL24W	$69 RED Housing	Colored Light Strobe Wall Mount · 24VDC UL/CUL Listed · Low Profile, Universal Mounting Plate Included · Available colored light: amber, blue, green and red · Low Current Draw · Selectable Candela For applications with more than 1 line CLICK HERE
	$69 WHITE Housing
CSH24W	$79 RED Housing	Colored Light Strobe/Horn Wall Mount · 24VDC UL/CUL Listed · Low Profile, Universal Mounting Plate Included · Available colored light: amber, blue, green and red · Low Current Draw · Selectable Candela For applications with more than 1 line CLICK HERE
	$79 WHITE Housing
CSL24C	$69 RED Housing	Colored Light Strobe Ceiling Mount · 24VDC UL/CUL Listed · Universal Mounting with Optional Plate · Available colored light: amber, blue, green and red · Low Current Draw · Selectable Candela For applications with more than 1 line CLICK HERE
	$69 WHITE Housing
CSH24C	$89 RED Housing	Colored Light Strobe/Horn Ceiling Mount · 24VDC UL/CUL Listed · Universal Mounting with Optional Plate · Available colored light: amber, blue, green and red · Low Current Draw · Selectable Candela For applications with more than 1 line CLICK HERE
	$89 WHITE Housing
CSL24CH	$79 RED Housing	Colored Light Strobe Ceiling Mount · 24VDC UL/CUL Listed · Universal Mounting with Optional Plate · Available colored light: amber, blue, green and red · Low Current Draw For applications with more than 1 line CLICK HERE
	$79 WHITE Housing
CSH24CH	$89 RED Housing	Colored Light Strobe/Horn Ceiling Mount · 24VDC UL/CUL Listed · Universal Mounting with Optional Plate · Available colored light: amber, blue, green and red · Low Current Draw For applications with more than 1 line CLICK HERE
	$89 WHITE Housing
CSLB24	$99 RED Housing	Colored Light Strobe Outdoor · 24VDC UL/CUL Listed · Optional Back Box or Mounting Plate · Available colored light: amber, blue, green and red · Red or Gray Body For applications with more than 1 line CLICK HERE
	$99 GRAY Housing
CSLB120	$99 RED Housing	Colored Light Strobe Outdoor · 120VDC UL/CUL Outdoor Listed · Optional Back Box or Mounting Plate · Available colored light: amber, blue, green and red · Red or Gray Body For applications with more than 1 line CLICK HERE
	$99 GRAY Housing

Common Audible Control Units
Choice of two outputs for connection of alert signal: standard ringing voltage or dry contact closure	The CA312 & CA622 monitors multiple analog telephone lines (tip and ring) to provide all call signaling, zoned signaling or night bell connection. These control units also enable connection for operation of external audible or visual alerts to be operated directly off the telephone ring voltage output. Units can be cascaded to increase line coverage
		CA-312	CA-622
	Application...........	Up to 3 Tip & Ring Lines, 1 Zone	Up to 6 Tip & Ring Lines, 2 Zones
	Input Voltage.......	55-130V, 20-30 Hz	55-130V, 20-30 Hz
	Output....................	Ringing Voltage or Dry Contact Closure	Ringing Voltage or Dry Contact Closure
		Product Specs	Product Specs
		Discontinued	Discontinued

Provides the power to operate a wide variety of 24 VDC signaling products while isolation the load from the contact closure.

	Deliver 24 VDC at 300 mA via a dry contact closure
	Can be wall-mounted, comes with six-foot power cord
	Quick-connect input/output terminals require no special tool for hookup
	Can power multiple products
	One unit can activate another to power additional products

product specs.

Provide Line Status and Message Waiting Indication

When used with an analog phone line, the VR-1A will provide "ring" indication, "on the phone" indication and "message waiting" indication for both "stutter dial tone" and standard message waiting voltage. In this application the VR-1A connects directly to tip and ring.

When used with a headset, you can end those nagging interruptions that occur when associates’ don’t realize you are on the phone because you are using a headset. The VR-1A will flash twice indicating to everyone that you are on the phone and you are not to be disturbed. The VR-1A installs in the handset/headset jack using an included "T" adapter.

When used with electronic or digital phones, the VR-1A won’t have you guessing which phone is ringing in busy offices. The flashing LED can be seen up to 100 feet away. The VR-1A connects directly to the electronic phone’s speaker.

Features

Displays "ringing," "on-the-phone" or "message waiting"

LED visible up to 100 ft

Power supply included

Compact package mounts with double-back tape

Connects with modular cord Special "T" adapter provided for handset applications

One year warranty

Made in the USA

Specifications

Message Waiting Voltage: 90V - 125V

Power: 120V AC/12V DC 500mA UL listed adapter provided

Dimensions: 70mm x 50mm x 40mm (2.9" x 2.1" x 1.5")

Shipping Weight: 1lb.

Environmental: 0°C to 32°C (32°F to 90°F) with 5% to 95% non-condensing humidity

Connections: (1) RJ14 jack

Light: 19mm (.75") red LED

Visibility: 30m (100’) typical

Applications

	Call centers
	Telemarketing Product support groups
	Office cubicles
	C.O. based voice messaging
	Purchasing departments
	Sales offices

	Super loud telephone ringer (95+ decibels)
	Visual ring indicator
	Adjustable ring volume
	Adjustable ring tone control (250-1200Hz)
	Choice of four distinct ring patterns
	Dual modular phone jacks for easy connection to a standard analog telephone

product specs.

Provide Visual Lamp Indication of Message Waiting and Ringing

The message waiting lamp retrofit kit is compatible with any telephone system with standard DC message waiting voltages ranging from 90VDC to 120 VDC.

The LM-1A is fully modular for quick plug-in installation by non-telephone personnel. The unit’s LED will blink at a steady rate when the message waiting voltage is detected.

The LM-1A will also flicker when the phone rings, helping to reduce noise in quiet areas by providing a convenient visual indication for ringing or message waiting.

Note: The LM-1A is not compatible with any AT&T phone system

Features

Attractive styling

Easy retrofit mounting

Works with nearly all message waiting voltages

One year warranty

Made in the USA

Specifications

Input: 80V DC to 150V DC message waiting voltage, minimum 40V AC ring voltage

Viewing Distance: Up to 15m (50 feet)

Dimensions: 65mm x 35mm x 20mm (2.56” x 1.38” x .79”)

Shipping Weight: 0.45 kg (1 lbs)

Environmental: 0° C to 32° C (32° F to 90° F) with 5% to 95% non-condensing humidity